Translate this page

Pages are written in English and translated in your browser by machine translation. Test results and your data are never sent anywhere.

Left Right Sound Test for Speakers and Headphones

Press left or right and listen. The voice should come only from that side; if it does not, your channels are swapped or one side is weak.

Runs locally in your browser. Nothing is uploaded.

Lower your volume first. Start with your device volume at about a third, then raise it slowly. Tests start quiet.

Captions appear here while a sound plays.

Did “Left” come only from the left?
Did “Right” come only from the right?

Stereo sweep

Soft noise moves from left to right and back for eight seconds. It should travel smoothly, without jumping or dropping out in the middle.

Frequency sweep

A tone glides from low to high (or high to low). Press “I can’t hear it” when it disappears to find the range your headphones and ears reach together.

–

Bass

Low tones show how deep your headphones go. Small laptop and phone speakers often cannot play below 100 Hz at all.

Polarity (phase)

Play both. “In phase” should sound solid and centered. “Out of phase” should sound wide, hollow, and thin in the bass. If the out-of-phase one sounds more centered, one speaker or ear cup is wired backwards.

Results

Answer the two questions above
Left channel–
Right channel–
Lowest heard–
Highest heard–
Output channels–

The left right sound test plays a spoken message in one channel at a time: “This is the left channel” from the left, “This is the right channel” from the right. It is the quickest way to confirm your headphones or speakers are not swapped, that both sides work, and that nothing is forcing your audio into mono.

6 chapters · 2 min read

How to use the left right test

1 min
  1. Put on your headphones, matching the L and R marks, or sit centered between your speakers.
  2. Lower your device volume to about a third.
  3. Press Left. You should hear the message only in your left ear.
  4. Press Right. You should hear it only in your right ear.
  5. Press Center to hear the voice from both sides at once; it should sound like it comes from the middle of your head.
  6. Answer the two questions under the buttons. The result tells you if everything is correct, if one side has a problem, or if the channels are swapped.
  7. Play the stereo sweep to check for dropouts as the sound moves across.

How it works

1 min

The voice clips are recorded in mono. The test sends each one through a stereo panner set fully to one side, so the other side receives silence, not a quieter copy. That makes even a small leak easy to notice: if you hear the left message faintly in your right ear, something in your setup is mixing the channels.

How to read your result

1 min
What you hearWhat it meansWhat to do
Each message on its own sideCorrect stereo.Nothing.
Left message on the right and right on the leftChannels swapped.Turn headphones around, swap speaker cables, or check audio software.
Both messages in both earsMono audio is on, or a virtual surround effect mixes channels.Turn off mono audio and spatial or surround effects.
One message missingThat side, its cable or the balance setting has a problem.Re-seat the plug, check balance, try another device.

Where to check settings

1 min

Windows 11: Settings > Accessibility > Audio > Mono audio. Balance is in Settings > System > Sound > your output > Left and Right.

macOS: System Settings > Accessibility > Audio > Play stereo audio as mono. Balance is in System Settings > Sound > Output.

iPhone: Settings > Accessibility > Audio & Visual > Mono Audio and Balance.

Android: Settings > Accessibility > Audio adjustment (names vary by maker).

Why left and right matter

1 min

In games, swapped channels put footsteps on the wrong side. In music and films, they flip the stage. In video calls, they are harmless, but a one-sided fault can mean a cable is about to fail.

Want a deeper check? The headphone test adds bass, sweep and phase tests, and the speaker test covers surround. The home page lists every audio test.

Fix guides for common problems

1 min

Frequently asked questions

How do I do a left right sound test?

Put on headphones, lower the volume, and press Left and then Right. You should hear "This is the left channel" only in your left ear and "This is the right channel" only in your right ear. Answer the two questions to get a verdict.

Why is my left and right audio reversed?

Headphones may be on backwards, speaker cables may be swapped, or a setting may be reversing channels. Check the L and R marks on your headphones, swap speaker cables, and turn off any "swap channels" option in your audio software.

Why do I hear sound in only one ear?

A plug not pushed in fully, a damaged cable near the plug, a balance setting, or mono audio turned on in accessibility settings. Our guide on one headphone side not working covers each cause.

Can I do this test with Bluetooth earbuds?

Yes. Make sure both earbuds are connected; many earbuds play mono when only one is in.

What is mono audio?

A setting that sends the same sound to both ears. It is useful for people with hearing in one ear, but it makes left-right tests sound centered. Turn it off in accessibility settings to test channels.

Sources

  1. MDN Web Docs: StereoPannerNode
  2. Wikipedia: Stereophonic sound

Written and tested by Kamel Medlej

Founder and editor of PC Hardware Tester. Tools are checked on real hardware, and each page says exactly what it was tested on. Spot a mistake? Tell us.

Last updated Published Tested on Chromium-based browser on Windows 11 with wired stereo headphones, during development. Other browsers and devices are added here as they are checked.