Translate this page

Pages are written in English and translated in your browser by machine translation. Test results and your data are never sent anywhere.

Speaker Test: Check Channels, Bass and Range

Hear each channel announce itself, sweep across the stereo field, and run the full frequency range from deep bass to treble.

Runs locally in your browser. Nothing is uploaded.

Lower your volume first. Start with your device volume at about a third, then raise it slowly. Tests start quiet.

Captions appear here while a sound plays.

Did “Left” come only from the left?
Did “Right” come only from the right?

Stereo sweep

Soft noise moves from left to right and back for eight seconds. It should travel smoothly, without jumping or dropping out in the middle.

Frequency sweep

A tone glides from low to high (or high to low). Press “I can’t hear it” when it disappears to find the range your speakers and ears reach together.

–

Bass

Low tones show how deep your speakers or subwoofer go. Small laptop and phone speakers often cannot play below 100 Hz at all.

Polarity (phase)

Play both. “In phase” should sound solid and centered. “Out of phase” should sound wide, hollow, and thin in the bass. If the out-of-phase one sounds more centered, one speaker or ear cup is wired backwards.

Surround channels

Play any sound above first. Browsers report how many output channels you have only after audio starts.

Results

Answer the two questions above
Left channel–
Right channel–
Lowest heard–
Highest heard–
Output channels–

A speaker test, sometimes called a sound test, checks that sound comes out of the right speaker, that your speakers cover the frequencies you expect, and that they are wired correctly. This one speaks each channel’s name from that speaker only, sweeps a tone from deep bass to treble, and tests surround systems when your browser supports them.

6 chapters · 3 min read

How to use the speaker test

1 min
  1. Lower your volume to about a third. Every test starts quiet, and you can raise the test volume with the slider.
  2. Press Left, Center and Right. A voice says each name from the matching speaker. Captions show what is playing.
  3. Answer Did “Left” come only from the left? and the same for Right. The result tells you if the channels are correct, missing or swapped.
  4. Play the stereo sweep. Soft noise should glide smoothly from left to right and back.
  5. Play the frequency sweep from 20 Hz to 20 kHz and press I can’t hear it when the tone fades. Do the downward sweep to find the lowest note.
  6. Try the bass tones from 30 to 100 Hz.
  7. Compare in phase and out of phase to check wiring.
  8. With a surround system, use the surround channel buttons.

How the sound test works

1 min

Every sound is made in your browser with the Web Audio API. The channel callouts are short mono voice recordings; the test places each one in a single channel with a stereo panner, so the word really comes only from that speaker. For surround, a channel merger routes the voice to one of up to eight outputs in the standard 5.1 or 7.1 order.

The tones are generated live by an oscillator, not loaded from a file, so the frequency is exact. The stereo and phase tests use pink noise, which has equal energy per octave and is easy to locate by ear. For the phase test, the right channel’s copy is flipped upside down; on correctly wired speakers that makes the sound feel wide and hollow.

How to read your speaker test

1 min
ResultMeaningWhat to do
Left and right correctStereo is working and in the right order.Nothing.
Both answers “No”Left and right are swapped.Swap the speaker cables or the left/right plugs.
One side silentThat speaker, its cable or its channel has a fault.Check the cable and the balance setting in your sound settings.
Sweep drops out in the middleA speaker may have a damaged driver.Play the sweep slowly and listen to each speaker.
Out of phase sounds more centeredOne speaker is wired backwards.Swap plus and minus on one speaker.

Common speaker problems and fixes

1 min

Sound only from one side. Open your system sound settings and check the balance for the output device. A loose 3.5 mm plug that is not fully inserted often plays only one channel.

No sound at all. Check that the right output device is selected, that it is not muted, and that the speakers are powered. On Windows, the volume mixer can mute a single browser.

Crackling or distortion. Lower the volume. If it persists at low volume, test another cable and another port, and check for interference from phone chargers.

Surround channels in the wrong place. Set the speaker configuration in your system (Windows: Sound > your device > Configure). Rear and side channels are often swapped on 7.1 systems.

Speaker terms in plain English

1 min
  • Channel: one separate audio signal, such as left or right.
  • Panning: placing a sound between the left and right speakers.
  • Frequency: how high or low a tone is, in hertz (Hz).
  • Phase: whether two speakers push air in the same direction at the same time.
  • 5.1: five main speakers plus one subwoofer.

Using headphones? The headphone test and the left right sound test are tuned for them. Check your microphone with the mic test, and see every test on the home page.

Fix guides for common problems

1 min

Frequently asked questions

How do I test my speakers online?

Lower your volume, then press Left, Center and Right. A voice says the name of each channel from that speaker only. If each word comes from the matching side, your stereo works. The sweeps and bass tones check range and wiring.

How do I know if my speakers are wired backwards?

Play the in-phase and out-of-phase sounds. In phase should sound solid and centered. Out of phase should sound wide and thin. If it is the other way round, one speaker's plus and minus wires are swapped.

Can I test 5.1 or 7.1 surround sound?

Yes, when your browser reports six or more output channels. Chrome and Edge on Windows do when the system speaker setup is set to 5.1 or 7.1. Each surround button speaks from one speaker only.

Why do my small speakers make no sound in the bass test?

Laptop, phone and small desktop speakers usually cannot play below about 100 Hz. Silence at 30 to 60 Hz is normal for them. A subwoofer or larger speakers are needed for deep bass.

Is the sound test safe for my speakers?

Yes at normal volume. Start low. Very loud low-frequency tones can stress small speakers, so raise the volume slowly and stop if you hear rattling or distortion.

Can I choose which speakers the sound plays from?

In Chrome and Edge, a device menu appears when your browser can list outputs. Otherwise, change the output in your system sound settings.

Sources

  1. MDN Web Docs: StereoPannerNode
  2. MDN Web Docs: AudioDestinationNode.maxChannelCount
  3. MDN Web Docs: AudioContext.setSinkId()
  4. Wikipedia: 5.1 surround sound

Written and tested by Kamel Medlej

Founder and editor of PC Hardware Tester. Tools are checked on real hardware, and each page says exactly what it was tested on. Spot a mistake? Tell us.

Last updated Published Tested on Chromium-based browser on Windows 11 with stereo desktop speakers, during development. Other browsers and speaker setups are added here as they are checked.