Translate this page

Pages are written in English and translated in your browser by machine translation. Test results and your data are never sent anywhere.

Headphone Test: Balance, Range and Phase

Check that both sides play evenly, find how low and high your headphones reach, and catch a phase or wiring fault.

Runs locally in your browser. Nothing is uploaded.

Lower your volume first. Start with your device volume at about a third, then raise it slowly. Tests start quiet.

Captions appear here while a sound plays.

Did “Left” come only from the left?
Did “Right” come only from the right?

Stereo sweep

Soft noise moves from left to right and back for eight seconds. It should travel smoothly, without jumping or dropping out in the middle.

Frequency sweep

A tone glides from low to high (or high to low). Press “I can’t hear it” when it disappears to find the range your headphones and ears reach together.

–

Bass

Low tones show how deep your headphones go. Small laptop and phone speakers often cannot play below 100 Hz at all.

Polarity (phase)

Play both. “In phase” should sound solid and centered. “Out of phase” should sound wide, hollow, and thin in the bass. If the out-of-phase one sounds more centered, one speaker or ear cup is wired backwards.

Results

Answer the two questions above
Left channel–
Right channel–
Lowest heard–
Highest heard–
Output channels–

The headphone test checks both ears, the range your headphones can reproduce, their bass, and their wiring. Start with the left and right callouts, then use the frequency sweep, bass tones and phase test to spot a weak driver, a loose cable or a one-sided fault.

6 chapters · 2 min read

How to use the headphone test

1 min
  1. Put your headphones on with L on your left ear. Lower your volume.
  2. Press Left and Right. Each word should come from one ear only. Answer the two questions.
  3. Play the stereo sweep and gently move the cable near the plug. Crackles or dropouts point to a damaged wire.
  4. Play the 20 Hz to 20 kHz sweep and press I can’t hear it when the tone fades. Then try the 400 to 20 Hz sweep for the low end.
  5. Try the bass tones. Good closed headphones usually reach 30 to 40 Hz; earbuds that do not seal often fade below 80 Hz.
  6. Compare in phase and out of phase.

How it works

1 min

Every tone is generated live by your browser, so frequencies are exact and nothing large is downloaded. Voice callouts are mono recordings placed fully in one channel, so any sound in the other ear comes from your setup, not from the file. The pink noise for the stereo and phase tests is made fresh each time.

How to read your headphone results

1 min
ResultWhat it suggests
Both channels correctStereo works.
One side quiet or silentLoose plug, broken wire, balance setting, or a failed driver.
Crackle when moving the cableDamaged wire, often near the plug or where the cable meets the ear cup.
Buzzing on bass tonesA rubbing voice coil or loose part; lower the volume and compare sides.
Low notes vanish earlyPoor seal (earbud tips too small) or headphones with limited bass.
Out of phase sounds centeredOne driver wired backwards.

The top of the frequency sweep depends on your ears as well as your headphones. For a guided screening of your hearing, see the hearing test, which is for information only.

Tips for a fair test

1 min
  • Turn off EQ, bass boost, spatial audio and “virtual surround” while testing.
  • For earbuds, try a larger tip size; a good seal changes the bass dramatically.
  • Compare with another pair of headphones on the same device to separate a headphone fault from a computer fault.

Common headphone problems

1 min

One side not working. Push the plug in all the way, check balance and mono audio, and try another device. Our guide on one headphone side not working covers each fix.

The headphone mic does not work. Many headsets use a four-pole plug. A computer jack with separate mic and headphone sockets needs a splitter. Test it with the mic test.

Sound is very quiet. Some high-impedance headphones need an amplifier. Check the output volume and any “absolute volume” setting for Bluetooth.

Related tests: the left right sound test, the speaker test and the mic test. The home page lists everything.

Fix guides for common problems

1 min

Frequently asked questions

How do I test my headphones?

Lower the volume, put them on, and press Left and Right to check each ear. Then play the frequency sweep, bass tones and phase test. Answer the two questions to get a verdict on the channels.

How can I tell if my headphones are damaged?

Signs include sound in only one ear, crackling when you move the cable, a buzzing driver on bass tones, or a weak, thin sound on the in-phase test. Wiggle the cable near the plug while playing the stereo sweep to find a loose wire.

Why can I not hear the highest tones?

The highest tone you hear depends on your headphones, the volume and your ears. Hearing at very high frequencies falls naturally with age, so stopping well below 20 kHz is common and is not a diagnosis.

Do Bluetooth headphones work with this test?

Yes. Bluetooth adds delay and compression, which do not affect these tests much. Make sure both earbuds are connected and mono audio is off.

What does the phase test tell me about headphones?

If out of phase sounds more solid than in phase, one ear cup's driver is wired backwards, which is rare but happens after repairs.

Sources

  1. MDN Web Docs: OscillatorNode
  2. Wikipedia: Hearing range
  3. MDN Web Docs: StereoPannerNode

Written and tested by Kamel Medlej

Founder and editor of PC Hardware Tester. Tools are checked on real hardware, and each page says exactly what it was tested on. Spot a mistake? Tell us.

Last updated Published Tested on Chromium-based browser on Windows 11 with wired stereo headphones, during development. Other browsers and headphones are added here as they are checked.