Translate this page

Pages are written in English and translated in your browser by machine translation. Test results and your data are never sent anywhere.

Controllers

How to Fix Controller Stick Drift

Fix controller stick drift on PS5, Xbox and PC. Measure drift online, then try cleaning, recalibration, dead zones, firmware and stick replacement, in order.

By Updated 3 min read

A generic game controller with motion trails around its thumbstick
Test it now: Controller Tester (buttons, triggers, sticks, drift, rumble)

Stick drift is when a controller reports movement while nobody touches the stick, so your character or camera creeps on its own. To fix it, first measure how bad it is, then clean around the stick, recalibrate, raise the dead zone, and replace the stick module if the drift is large or keeps getting worse.

9 chapters · 3 min read

Step 1: Measure the drift

1 min

Connect the controller and open the controller tester (or the PS5 or Xbox version). Put the controller down, press Measure stick drift, and keep your hands off for three seconds.

Idle readingWhat it means
Under 0.08Normal resting noise. No drift.
0.08 to 0.24Early drift. Small in-game dead zones may show it.
Over 0.24Clear drift. Most games will see movement.

The 0.24 line comes from the left-stick dead zone Microsoft recommends for XInput controllers. Measure a few times; drift often changes when the stick is warm or after you push it hard.

Why sticks drift

1 min

Most thumbsticks contain two potentiometers, one for each axis. A tiny wiper slides across a resistive track as you move the stick, and the controller reads the resistance to work out the position. Over months of use, the track wears and collects dust, so the reading at center is no longer quite center. That small error is drift.

Because it is wear, drift usually starts small and grows. Cleaning can help for a while; replacing the worn part fixes it.

Step 2: Clean around the stick

1 min
  1. Turn the controller off.
  2. Push the stick to one side and blow compressed air into the gap under the rubber cap.
  3. Rotate the stick in full circles, firmly, 20 to 30 times while you keep blowing.
  4. Repeat for every direction.
  5. Measure again.

Some people add a drop of isopropyl alcohol at the base of the stick and rotate it. If you try this, use a very small amount and let it dry completely before use.

Step 3: Recalibrate

1 min
  • Windows: search for Set up USB game controllers (joy.cpl), select the controller, Properties > Settings > Calibrate, and follow the steps.
  • Steam: Settings > Controller > select the controller > Calibrate. Steam can also set an outer and inner dead zone.
  • Consoles: update the controller firmware; some consoles do not offer a manual calibration screen.

Step 4: Raise the dead zone

1 min

A dead zone is a small area around center that the game ignores. Raising it hides drift at the cost of a little precision. Set it just above your measured drift. In the tester, drag the Dead zone overlay slider to see how big that is. Read what is a controller dead zone for how to choose.

Step 5: Update firmware

1 min

Controller makers sometimes improve calibration and filtering in firmware. Update through the console, the Xbox Accessories app on Windows, or the maker’s PC tool.

Step 6: Replace the stick module

1 min

If drift stays above the warning line after cleaning, the potentiometer is worn.

  • Warranty: contact the maker; drift is a known fault.
  • Repair service: replacing a stick module needs soldering on most controllers.
  • Hall effect or TMR sticks: many repair kits replace the original module with magnetic sensors that do not wear by rubbing.

Quick reference

1 min
SituationBest fix
Drift appeared suddenly after a dropRecalibrate, then clean
Slow creep only in one gameRaise that game’s dead zone
Drift grows over weeksReplace the module
Drift right out of the boxReturn or warranty

After any fix, measure again in the controller tester. If your controller does not connect at all, read controller not detected in Steam. Find every test on the home page.

PlayStation and Xbox are trademarks of their owners. This site is not affiliated with Sony or Microsoft.

Tools for this problem

1 min

Frequently asked questions

What causes stick drift?

Most controllers read stick position with small potentiometers, which wear and collect dust over time. The worn track gives a slightly wrong reading at rest, so the game sees movement when you are not touching the stick.

How do I check for stick drift?

Open the controller tester, leave both sticks alone, and press Measure stick drift. A reading above 0.08 suggests early drift; above 0.24 most games will notice it.

Can stick drift be fixed without opening the controller?

Sometimes. Cleaning around the stick with compressed air, rotating it firmly, recalibrating and raising the in-game dead zone can reduce or hide drift. Worn potentiometers need replacing for a lasting fix.

Is stick drift covered by warranty?

Usually yes during the warranty period, because it is a hardware fault. Keep your tester readings as evidence.

Do Hall effect sticks drift?

Hall effect and TMR sticks measure position with magnets instead of a rubbing track, so they do not wear the same way. They are a common replacement for drifting sticks.

Sources

  1. Microsoft: Getting started with XInput (dead zones)
  2. Wikipedia: Potentiometer
  3. Wikipedia: Hall effect sensor

Written and tested by Kamel Medlej

Founder and editor of PC Hardware Tester. Tools are checked on real hardware, and each page says exactly what it was tested on. Spot a mistake? Tell us.

Last updated Published